[RFCs/IDs] [Plain Text] [From draft-ietf-ipcdn-bpiplus-mib]
PROPOSED STANDARD
Network Working Group S. Green
Request for Comments: 4131 Consultant
Category: Standards Track K. Ozawa
Toshiba
E. Cardona, Ed.
CableLabs
A. Katsnelson
September 2005
Management Information Base for
Data Over Cable Service Interface Specification (DOCSIS) Cable Modems
and Cable Modem Termination Systems for Baseline Privacy Plus
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2005).
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it defines a set of managed objects for Simple Network
Management Protocol (SNMP) based management of the Baseline Privacy
Plus features of DOCSIS 1.1 and DOCSIS 2.0 (Data-over-Cable Service
Interface Specification) compliant Cable Modems and Cable Modem
Termination Systems.
Table of Contents
1. The Internet-Standard Management Framework..................... 2
2. Overview....................................................... 2
2.1. Structure of the MIB...................................... 3
2.2. Relationship of BPI+ and BPI MIB Modules.................. 4
2.3. BPI+ MIB Module Relationship with The Interfaces Group MIB 5
3. Definitions.................................................... 5
4. Acknowledgements............................................... 77
5. Normative References........................................... 77
6. Informative References......................................... 78
7. Security Considerations........................................ 79
8. IANA Considerations............................................ 83
Green, et al. Standards Track [Page 1]
RFC 4131 DOCSIS BPI Plus MIB September 2005
1. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to section 7 of
RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580].
2. Overview
This MIB module (BPI+ MIB) provides a set of objects required for the
management of the Baseline Privacy Interface Plus features of DOCSIS
1.1 and DOCSIS 2.0 Cable Modem (CM) and Cable Modem Termination
System (CMTS). The specification is derived from the operational
model described in the DOCSIS Baseline Privacy Interface Plus
Specification [DOCSIS].
DOCSIS Baseline Privacy Plus is composed of four distinct functional
and manageable areas:
o Key exchange and data encryption
o Cable modem authentication
o Multicast encryption
o Authentication of downloaded software images
This MIB module is an extension of the DOCSIS 1.0 Baseline Privacy
MIB module [RFC3083] (BPI MIB), which is derived from the Operational
model described in the DOCSIS Baseline Privacy Interface
Specification [DOCSIS-1.0]. The original Baseline Privacy MIB
structure has mostly been preserved in the Baseline Privacy Plus MIB.
Please note that the referenced DOCSIS specifications only require
that Cable Modems process IPv4 customer traffic. Design choices in
this MIB module reflect those requirements. Future versions of the
DOCSIS specifications are expected to require support for IPv6 as
well.
Green, et al. Standards Track [Page 2]
RFC 4131 DOCSIS BPI Plus MIB September 2005
Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL
NOT","SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL"
in this document are to be interpreted as described in BCP 14, RFC
2119 [RFC2119].
2.1. Structure of the MIB
This MIB module is structured into several tables and objects.
2.1.1. Cable Modem
o The docsBpi2CmBaseTable contains authorization key exchange
information for one CM MAC interface.
o The docsBpi2CmTEKTable contains traffic key exchange and data
encryption information for a particular security association ID of
the cable modem.
o Multicast Encryption information is maintained under
Docsbpi2CmMulticastObjects. There is currently one multicast
table object that manages IP multicast encryption,
docsBpi2CmIpMulticastMapTable.
o Digital certificates used for cable modem authentication are
accessible via docsBpi2CmDeviceCertTable.
o Cryptographic suite capabilities for a CM MAC are maintained in
the docsBpi2CmCryptoSuiteTable.
2.1.2. Cable Modem Termination System
o The docsBpi2CmtsBaseTable contains default settings and summary
counters for the cable modem termination system.
o The DocsBpi2CmtsAuthTable contains Authorization Key Exchange
information for each CM MAC interface, as well as data from CM
certificates used in cable modem authentication.
o The docsBpi2CmtsTEKTable contains traffic key exchange and data
encryption information for a particular security association ID.
o Multicast Encryption information is maintained under
Docsbpi2CmtsMulticastObjects. There are currently two multicast
table objects. The Table docsBpi2CmtsIpMulticastMapTable is
Green, et al. Standards Track [Page 3]
RFC 4131 DOCSIS BPI Plus MIB September 2005
specifically designed for IP multicast encryption, whereas
docsBpi2CmtsMulticastAuthTable is meant to manage all multicast
security associations.
In particular, the table docsBpi2CmtsIpMulticastMapTable
defines the object docsBpi2CmtsIpMulticastMask, which could be
a non-contiguous netmask; this is why the object syntax is
based on the INET-ADDRESS-MIB MIB Module [RFC4001] Textual
Convention InetAddress instead of InetAddressPrefixLength.
This is to facilitate the assignment of same DOCSIS Security
Association ID (SAID) to one or more IPv6 multicast group IDs
matching one or more IPv6 multicast scope types within an entry
in this table. For example, multicast scopes labeled
"unassigned" [RFC3513] may be allocated by administrators to a
particular SAID, regardless of their multicast scope; such
mapping transient multicast group 'Y' to SAID 'z' for ANY
multicast scope. The non-contiguous netmask will be FF10:Y.
See [RFC3513] for details on IPv6 multicast addressing.
o DocsBpi2CmtsCertObjects contains 2 manageable tables: one for
provisioned cable modem certificates and one for certification
authority certificates.
2.1.3. Common
o The docsBpi2CodeDownloadControl objects manage the authenticated
software download process for a given device.
2.2. Relationship of BPI+ and BPI MIB Modules
This section describes the relationship between the BPI+ MIB module
defined in this document and the BPI MIB module defined in RFC 3083
[RFC3083]. The BPI+ protocol interface is an enhancement to the BPI
protocol, and it is a distinct protocol from BPI. The associated
BPI+ managed objects should be considered separate from the BPI MIB
objects defined in RFC 3083.
DOCSIS 1.1 and 2.0 systems implement both the BPI+ and BPI protocols
to be backward compatible with 1.0 systems. For more information
regarding the interoperability between BPI and BPI+ compliant
systems, refer to appendix C of the DOCSIS BPI+ specification
[DOCSIS]. For MIB modules requirements, refer to section 4.6.1,
Figure 9, of the DOCSIS 1.1 OSSI specification [DOCSIS-1.1] and to
section 7.6.1, Tables 7-9, of the DOCSIS 2.0 OSSI specification
[DOCSIS-2.0].
Green, et al. Standards Track [Page 4]
RFC 4131 DOCSIS BPI Plus MIB September 2005
2.3. BPI+ MIB Module Relationship with the Interfaces Group MIB
The BPI+ MIB module is the management framework of Baseline Privacy
Plus Interface Specification [DOCSIS], which provides the MAC layer
(Media Access Control) security services of DOCSIS through the
Baseline Privacy Key Management (BPKM) protocol. The BPI+ MIB module
objects are organized as extensions of the Radio Frequency (RF)
Interface Management [RFC2670].
The MIB table structures of this MIB Module are extensions of the
DOCSIS CATV (Community Antenna Television) MAC layer interface
(DocsCableMaclayer by [IANA]). In particular, the provisions of the
Interface Group MIB [RFC2863] for counter discontinuities and system
re-initialization apply to CM and CMTS to validate the difference
between two consecutive counter polls.
All BPI+ MIB module counters are 32 bits and are based on the minimum
time to wrap up considerations of [RFC2863] and their possible
frequency occurrence as BPI+ FSM (Finite State Machine) event
counters. See [DOCSIS] for BPI+ FSM parameter guidelines.
3. Definitions
DOCS-IETF-BPI2-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Integer32,
Unsigned32,
Counter32,
mib-2
FROM SNMPv2-SMI -- [RFC2578]
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- [RFC3411]
TEXTUAL-CONVENTION,
MacAddress,
RowStatus,
TruthValue,
DateAndTime,
StorageType
FROM SNMPv2-TC -- [RFC2579]
OBJECT-GROUP,
MODULE-COMPLIANCE
FROM SNMPv2-CONF -- [RFC2580]
ifIndex
FROM IF-MIB -- [RFC2863]
InetAddressType,
InetAddress
Green, et al. Standards Track [Page 5]
RFC 4131 DOCSIS BPI Plus MIB September 2005
FROM INET-ADDRESS-MIB; -- [RFC4001]
docsBpi2MIB MODULE-IDENTITY
LAST-UPDATED "200507200000Z" -- July 20, 2005
ORGANIZATION "IETF IP over Cable Data Network (IPCDN)
Working Group"
CONTACT-INFO "---------------------------------------
Stuart M. Green
E-mail: rubbersoul3@yahoo.com
---------------------------------------
Kaz Ozawa
Automotive Systems Development Center
TOSHIBA CORPORATION
1-1, Shibaura 1-Chome
Minato-ku, Tokyo 105-8001
Japan
Phone: +81-3-3457-8569
Fax: +81-3-5444-9325
E-mail: Kazuyoshi.Ozawa@toshiba.co.jp
---------------------------------------
Alexander Katsnelson
Postal:
Tel: +1-303-680-3924
E-mail: katsnelson6@peoplepc.com
---------------------------------------
Eduardo Cardona
Postal:
Cable Television Laboratories, Inc.
858 Coal Creek Circle
Louisville, CO 80027- 9750
U.S.A.
Tel: +1 303 661 9100
Fax: +1 303 661 9199
E-mail: e.cardona@cablelabs.com
---------------------------------------
IETF IPCDN Working Group
General Discussion: ipcdn@ietf.org
Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn.
Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn.
Co-chairs: Richard Woundy, rwoundy@cisco.com
Jean-Francois Mule, jfm@cablelabs.com"
DESCRIPTION
"This is the MIB module for the DOCSIS Baseline
Privacy Plus Interface (BPI+) at cable modems (CMs)
and cable modem termination systems (CMTSs).
Copyright (C) The Internet Society (2005). This
Green, et al. Standards Track [Page 6]
RFC 4131 DOCSIS BPI Plus MIB September 2005
version of this MIB module is part of RFC 4131; see
the RFC itself for full legal notices."
REVISION "200507200000Z" -- July 20, 2005
DESCRIPTION
"Initial version of the IETF BPI+ MIB module.
This version published as RFC 4131."
::= { mib-2 126 }
-- Textual conventions
DocsX509ASN1DEREncodedCertificate ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"An X509 digital certificate encoded as an ASN.1 DER
object."
SYNTAX OCTET STRING (SIZE (0..4096))
DocsSAId ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"Security Association identifier (SAID)."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface
specification, Section 2.1.3, BPI+ Security
Associations"
SYNTAX Integer32 (1..16383)
DocsSAIdOrZero ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"Security Association identifier (SAID). The value
zero indicates that the SAID is yet to be determined."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface
specification, Section 2.1.3, BPI+ Security
Associations"
SYNTAX Unsigned32 (0 | 1..16383)
DocsBpkmSAType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The type of security association (SA).
The values of the named-numbers are associated
with the BPKM SA-Type attributes:
'primary' corresponds to code '1', 'static' to code '2',
Green, et al. Standards Track [Page 7]
RFC 4131 DOCSIS BPI Plus MIB September 2005
and 'dynamic' to code '3'.
The 'none' value must only be used if the SA type has yet
to be determined."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface
specification, Section 4.2.2.24"
SYNTAX INTEGER {
none(0),
primary(1),
static(2),
dynamic(3)
}
DocsBpkmDataEncryptAlg ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The list of data encryption algorithms defined for
the DOCSIS interface in the BPKM cryptographic-suite
parameter. The value 'none' indicates that the SAID
being referenced has no data encryption."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.20."
SYNTAX INTEGER {
none(0),
des56CbcMode(1),
des40CbcMode(2),
t3Des128CbcMode(3),
aes128CbcMode(4),
aes256CbcMode(5)
}
DocsBpkmDataAuthentAlg ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The list of data integrity algorithms defined for the
DOCSIS interface in the BPKM cryptographic-suite parameter.
The value 'none' indicates that no data integrity is used for
the SAID being referenced."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.20."
SYNTAX INTEGER {
none(0),
hmacSha196(1)
}
docsBpi2MIBObjects OBJECT IDENTIFIER ::= { docsBpi2MIB 1 }
Green, et al. Standards Track [Page 8]
RFC 4131 DOCSIS BPI Plus MIB September 2005
-- Cable Modem Group
docsBpi2CmObjects OBJECT IDENTIFIER ::= { docsBpi2MIBObjects 1 }
--
-- The BPI+ base and authorization table for CMs,
-- indexed by ifIndex
--
docsBpi2CmBaseTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpi2CmBaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the basic and authorization-
related Baseline Privacy Plus attributes of each CM MAC
interface."
::= { docsBpi2CmObjects 1 }
docsBpi2CmBaseEntry OBJECT-TYPE
SYNTAX DocsBpi2CmBaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing attributes of
one CM MAC interface. An entry in this table exists for
each ifEntry with an ifType of docsCableMaclayer(127)."
INDEX { ifIndex }
::= { docsBpi2CmBaseTable 1 }
DocsBpi2CmBaseEntry ::= SEQUENCE {
docsBpi2CmPrivacyEnable TruthValue,
docsBpi2CmPublicKey OCTET STRING,
docsBpi2CmAuthState INTEGER,
docsBpi2CmAuthKeySequenceNumber Integer32,
docsBpi2CmAuthExpiresOld DateAndTime,
docsBpi2CmAuthExpiresNew DateAndTime,
docsBpi2CmAuthReset TruthValue,
docsBpi2CmAuthGraceTime Integer32,
docsBpi2CmTEKGraceTime Integer32,
docsBpi2CmAuthWaitTimeout Integer32,
docsBpi2CmReauthWaitTimeout Integer32,
docsBpi2CmOpWaitTimeout Integer32,
docsBpi2CmRekeyWaitTimeout Integer32,
docsBpi2CmAuthRejectWaitTimeout Integer32,
docsBpi2CmSAMapWaitTimeout Integer32,
docsBpi2CmSAMapMaxRetries Integer32,
docsBpi2CmAuthentInfos Counter32,
Green, et al. Standards Track [Page 9]
RFC 4131 DOCSIS BPI Plus MIB September 2005
docsBpi2CmAuthRequests Counter32,
docsBpi2CmAuthReplies Counter32,
docsBpi2CmAuthRejects Counter32,
docsBpi2CmAuthInvalids Counter32,
docsBpi2CmAuthRejectErrorCode INTEGER,
docsBpi2CmAuthRejectErrorString SnmpAdminString,
docsBpi2CmAuthInvalidErrorCode INTEGER,
docsBpi2CmAuthInvalidErrorString SnmpAdminString
}
docsBpi2CmPrivacyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies whether this CM is
provisioned to run Baseline Privacy Plus."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1."
::= { docsBpi2CmBaseEntry 1 }
docsBpi2CmPublicKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..524))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is a DER-encoded
RSAPublicKey ASN.1 type string, as defined in the RSA
Encryption Standard (PKCS #1), corresponding to the
public key of the CM."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.4."
::= { docsBpi2CmBaseEntry 2 }
docsBpi2CmAuthState OBJECT-TYPE
SYNTAX INTEGER {
start(1),
authWait(2),
authorized(3),
reauthWait(4),
authRejectWait(5),
silent(6)
}
MAX-ACCESS read-only
STATUS current
Green, et al. Standards Track [Page 10]
RFC 4131 DOCSIS BPI Plus MIB September 2005
DESCRIPTION
"The value of this object is the state of the CM
authorization FSM. The start state indicates that FSM is
in its initial state."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.1.2.1."
::= { docsBpi2CmBaseEntry 3 }
docsBpi2CmAuthKeySequenceNumber OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the most recent
authorization key sequence number for this FSM."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.2 and 4.2.2.10."
::= { docsBpi2CmBaseEntry 4 }
docsBpi2CmAuthExpiresOld OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time for
expiration of the immediate predecessor of the most recent
authorization key for this FSM. If this FSM has only one
authorization key, then the value is the time of activation
of this FSM."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.2 and 4.2.2.9."
::= { docsBpi2CmBaseEntry 5 }
docsBpi2CmAuthExpiresNew OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time for
expiration of the most recent authorization key for this
FSM."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.2 and 4.2.2.9."
::= { docsBpi2CmBaseEntry 6 }
Green, et al. Standards Track [Page 11]
RFC 4131 DOCSIS BPI Plus MIB September 2005
docsBpi2CmAuthReset OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to 'true' generates a Reauthorize
event in the authorization FSM. Reading this object always
returns FALSE.
This object is for testing purposes only, and therefore it
is not required to be associated with a last reset
object."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.1.2.3.4."
::= { docsBpi2CmBaseEntry 7 }
docsBpi2CmAuthGraceTime OBJECT-TYPE
SYNTAX Integer32 (1..6047999)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the grace time for an
authorization key in seconds. A CM is expected to start
trying to get a new authorization key beginning
AuthGraceTime seconds before the most recent authorization
key actually expires."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1.1.3."
::= { docsBpi2CmBaseEntry 8 }
docsBpi2CmTEKGraceTime OBJECT-TYPE
SYNTAX Integer32 (1..302399)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the grace time for
the TEK in seconds. The CM is expected to start trying to
acquire a new TEK beginning TEK GraceTime seconds before
the expiration of the most recent TEK."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1.1.6."
::= { docsBpi2CmBaseEntry 9 }
Green, et al. Standards Track [Page 12]
RFC 4131 DOCSIS BPI Plus MIB September 2005
docsBpi2CmAuthWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..30)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Authorize Wait
Timeout in seconds."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1.1.1."
::= { docsBpi2CmBaseEntry 10 }
docsBpi2CmReauthWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..30)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Reauthorize Wait
Timeout in seconds."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1.1.2."
::= { docsBpi2CmBaseEntry 11 }
docsBpi2CmOpWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..10)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Operational Wait
Timeout in seconds."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1.1.4."
::= { docsBpi2CmBaseEntry 12 }
docsBpi2CmRekeyWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..10)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Rekey Wait Timeout
in seconds."
REFERENCE
Green, et al. Standards Track [Page 13]
RFC 4131 DOCSIS BPI Plus MIB September 2005
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1.1.5."
::= { docsBpi2CmBaseEntry 13 }
docsBpi2CmAuthRejectWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..600)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Authorization Reject
Wait Timeout in seconds."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1.1.7."
::= { docsBpi2CmBaseEntry 14 }
docsBpi2CmSAMapWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..10)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the retransmission
interval, in seconds, of SA Map Requests from the MAP Wait
state."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1.1.8."
::= { docsBpi2CmBaseEntry 15 }
docsBpi2CmSAMapMaxRetries OBJECT-TYPE
SYNTAX Integer32 (0..10)
UNITS "count"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the maximum number of
Map Request retries allowed."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.1.1.1.9."
::= { docsBpi2CmBaseEntry 16 }
docsBpi2CmAuthentInfos OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Green, et al. Standards Track [Page 14]
RFC 4131 DOCSIS BPI Plus MIB September 2005
DESCRIPTION
"The value of this object is the number of times
the CM has transmitted an Authentication Information
message. Discontinuities in the value of this counter can
occur at re-initialization of the management system, and at
other times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.9."
::= { docsBpi2CmBaseEntry 17 }
docsBpi2CmAuthRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the CM
has transmitted an Authorization Request message.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.1."
::= { docsBpi2CmBaseEntry 18 }
docsBpi2CmAuthReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the CM
has received an Authorization Reply message.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.2."
::= { docsBpi2CmBaseEntry 19 }
docsBpi2CmAuthRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Green, et al. Standards Track [Page 15]
RFC 4131 DOCSIS BPI Plus MIB September 2005
DESCRIPTION
"The value of this object is the number of times the CM
has received an Authorization Reject message.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.3."
::= { docsBpi2CmBaseEntry 20 }
docsBpi2CmAuthInvalids OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CM
has received an Authorization Invalid message.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.7."
::= { docsBpi2CmBaseEntry 21 }
docsBpi2CmAuthRejectErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedCm(3),
unauthorizedSaid(4),
permanentAuthorizationFailure(8),
timeOfDayNotAcquired(11)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated
description of the Error-Code in the most recent
Authorization Reject message received by the CM. This has
the value unknown(2) if the last Error-Code value was 0 and
none(1) if no Authorization Reject message has been received
since reboot."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Green, et al. Standards Track [Page 16]
RFC 4131 DOCSIS BPI Plus MIB September 2005
Sections 4.2.1.3 and 4.2.2.15."
::= { docsBpi2CmBaseEntry 22 }
docsBpi2CmAuthRejectErrorString OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the text string in the
most recent Authorization Reject message received by the
CM. This is a zero length string if no Authorization
Reject message has been received since reboot."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.3 and 4.2.2.6."
::= { docsBpi2CmBaseEntry 23 }
docsBpi2CmAuthInvalidErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedCm(3),
unsolicited(5),
invalidKeySequence(6),
keyRequestAuthenticationFailure(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated
description of the Error-Code in the most recent
Authorization Invalid message received by the CM. This has
the value unknown(2) if the last Error-Code value was 0 and
none(1) if no Authorization Invalid message has been received
since reboot."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.7 and 4.2.2.15."
::= { docsBpi2CmBaseEntry 24 }
docsBpi2CmAuthInvalidErrorString OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the text string in the
most recent Authorization Invalid message received by the
CM. This is a zero length string if no Authorization
Green, et al. Standards Track [Page 17]
RFC 4131 DOCSIS BPI Plus MIB September 2005
Invalid message has been received since reboot."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.7 and 4.2.2.6."
::= { docsBpi2CmBaseEntry 25 }
--
-- The CM TEK Table, indexed by ifIndex and SAID
--
docsBpi2CmTEKTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpi2CmTEKEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the attributes of each CM
Traffic Encryption Key (TEK) association. The CM maintains
(no more than) one TEK association per SAID per CM MAC
interface."
::= { docsBpi2CmObjects 2 }
docsBpi2CmTEKEntry OBJECT-TYPE
SYNTAX DocsBpi2CmTEKEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing the TEK
association attributes of one SAID. The CM MUST create one
entry per SAID, regardless of whether the SAID was obtained
from a Registration Response message, from an Authorization
Reply message, or from any dynamic SAID establishment
mechanisms."
INDEX { ifIndex, docsBpi2CmTEKSAId }
::= { docsBpi2CmTEKTable 1 }
DocsBpi2CmTEKEntry ::= SEQUENCE {
docsBpi2CmTEKSAId DocsSAId,
docsBpi2CmTEKSAType DocsBpkmSAType,
docsBpi2CmTEKDataEncryptAlg DocsBpkmDataEncryptAlg,
docsBpi2CmTEKDataAuthentAlg DocsBpkmDataAuthentAlg,
docsBpi2CmTEKState INTEGER,
docsBpi2CmTEKKeySequenceNumber Integer32,
docsBpi2CmTEKExpiresOld DateAndTime,
docsBpi2CmTEKExpiresNew DateAndTime,
docsBpi2CmTEKKeyRequests Counter32,
docsBpi2CmTEKKeyReplies Counter32,
docsBpi2CmTEKKeyRejects Counter32,
docsBpi2CmTEKInvalids Counter32,
Green, et al. Standards Track [Page 18]
RFC 4131 DOCSIS BPI Plus MIB September 2005
docsBpi2CmTEKAuthPends Counter32,
docsBpi2CmTEKKeyRejectErrorCode INTEGER,
docsBpi2CmTEKKeyRejectErrorString SnmpAdminString,
docsBpi2CmTEKInvalidErrorCode INTEGER,
docsBpi2CmTEKInvalidErrorString SnmpAdminString
}
docsBpi2CmTEKSAId OBJECT-TYPE
SYNTAX DocsSAId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is the DOCSIS Security
Association ID (SAID)."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.12."
::= { docsBpi2CmTEKEntry 1 }
docsBpi2CmTEKSAType OBJECT-TYPE
SYNTAX DocsBpkmSAType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the type of security
association."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 2.1.3."
::= { docsBpi2CmTEKEntry 2 }
docsBpi2CmTEKDataEncryptAlg OBJECT-TYPE
SYNTAX DocsBpkmDataEncryptAlg
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the data encryption
algorithm for this SAID."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.20."
::= { docsBpi2CmTEKEntry 3 }
docsBpi2CmTEKDataAuthentAlg OBJECT-TYPE
SYNTAX DocsBpkmDataAuthentAlg
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Green, et al. Standards Track [Page 19]
RFC 4131 DOCSIS BPI Plus MIB September 2005
"The value of this object is the data authentication
algorithm for this SAID."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.20."
::= { docsBpi2CmTEKEntry 4 }
docsBpi2CmTEKState OBJECT-TYPE
SYNTAX INTEGER {
start(1),
opWait(2),
opReauthWait(3),
operational(4),
rekeyWait(5),
rekeyReauthWait(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the state of the
indicated TEK FSM. The start(1) state indicates that the
FSM is in its initial state."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.1.3.1."
::= { docsBpi2CmTEKEntry 5 }
docsBpi2CmTEKKeySequenceNumber OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the most recent TEK
key sequence number for this TEK FSM."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.2.10 and 4.2.2.13."
::= { docsBpi2CmTEKEntry 6 }
docsBpi2CmTEKExpiresOld OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time for
expiration of the immediate predecessor of the most recent
TEK for this FSM. If this FSM has only one TEK, then the
value is the time of activation of this FSM."
Green, et al. Standards Track [Page 20]
RFC 4131 DOCSIS BPI Plus MIB September 2005
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.5 and 4.2.2.9."
::= { docsBpi2CmTEKEntry 7 }
docsBpi2CmTEKExpiresNew OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time for
expiration of the most recent TEK for this FSM."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.5 and 4.2.2.9."
::= { docsBpi2CmTEKEntry 8 }
docsBpi2CmTEKKeyRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the CM
has transmitted a Key Request message.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.4."
::= { docsBpi2CmTEKEntry 9 }
docsBpi2CmTEKKeyReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the CM
has received a Key Reply message, including a message whose
authentication failed.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Green, et al. Standards Track [Page 21]
RFC 4131 DOCSIS BPI Plus MIB September 2005
Section 4.2.1.5."
::= { docsBpi2CmTEKEntry 10 }
docsBpi2CmTEKKeyRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the CM
has received a Key Reject message, including a message
whose authentication failed.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.6."
::= { docsBpi2CmTEKEntry 11 }
docsBpi2CmTEKInvalids OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the CM
has received a TEK Invalid message, including a message
whose authentication failed.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.8."
::= { docsBpi2CmTEKEntry 12 }
docsBpi2CmTEKAuthPends OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times an
Authorization Pending (Auth Pend) event occurred in this
FSM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
Green, et al. Standards Track [Page 22]
RFC 4131 DOCSIS BPI Plus MIB September 2005
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.1.3.3.3."
::= { docsBpi2CmTEKEntry 13 }
docsBpi2CmTEKKeyRejectErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedSaid(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated
description of the Error-Code in the most recent Key Reject
message received by the CM. This has the value unknown(2) if
the last Error-Code value was 0 and none(1) if no Key
Reject message has been received since registration."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.1.2.6 and 4.2.2.15."
::= { docsBpi2CmTEKEntry 14 }
docsBpi2CmTEKKeyRejectErrorString OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the text string in the
most recent Key Reject message received by the CM. This is
a zero length string if no Key Reject message has been
received since registration."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.1.2.6 and 4.2.2.6."
::= { docsBpi2CmTEKEntry 15 }
docsBpi2CmTEKInvalidErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
invalidKeySequence(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Green, et al. Standards Track [Page 23]
RFC 4131 DOCSIS BPI Plus MIB September 2005
"The value of this object is the enumerated
description of the Error-Code in the most recent TEK Invalid
message received by the CM. This has the value unknown(2) if
the last Error-Code value was 0 and none(1) if no TEK
Invalid message has been received since registration."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.1.2.8 and 4.2.2.15."
::= { docsBpi2CmTEKEntry 16 }
docsBpi2CmTEKInvalidErrorString OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the text string in the
most recent TEK Invalid message received by the CM. This is
a zero length string if no TEK Invalid message has been
received since registration."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.1.2.8 and 4.2.2.6."
::= { docsBpi2CmTEKEntry 17 }
--
-- The CM Multicast Objects Group
--
docsBpi2CmMulticastObjects OBJECT IDENTIFIER
::= { docsBpi2CmObjects 3 }
--
-- The CM Dynamic IP Multicast Mapping Table, indexed by
-- docsBpi2CmIpMulticastIndex and by ifIndex
--
docsBpi2CmIpMulticastMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpi2CmIpMulticastMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table maps multicast IP addresses to SAIDs per
CM MAC Interface.
It is intended to map multicast IP addresses associated
with SA MAP Request messages."
::= { docsBpi2CmMulticastObjects 1 }
docsBpi2CmIpMulticastMapEntry OBJECT-TYPE
Green, et al. Standards Track [Page 24]
RFC 4131 DOCSIS BPI Plus MIB September 2005
SYNTAX DocsBpi2CmIpMulticastMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing the mapping of
one multicast IP address to one SAID, as well as
associated state, message counters, and error information.
An entry may be removed from this table upon the reception
of an SA Map Reject."
INDEX { ifIndex, docsBpi2CmIpMulticastIndex }
::= { docsBpi2CmIpMulticastMapTable 1 }
DocsBpi2CmIpMulticastMapEntry ::= SEQUENCE {
docsBpi2CmIpMulticastIndex Unsigned32,
docsBpi2CmIpMulticastAddressType InetAddressType,
docsBpi2CmIpMulticastAddress InetAddress,
docsBpi2CmIpMulticastSAId DocsSAIdOrZero,
docsBpi2CmIpMulticastSAMapState INTEGER,
docsBpi2CmIpMulticastSAMapRequests Counter32,
docsBpi2CmIpMulticastSAMapReplies Counter32,
docsBpi2CmIpMulticastSAMapRejects Counter32,
docsBpi2CmIpMulticastSAMapRejectErrorCode INTEGER,
docsBpi2CmIpMulticastSAMapRejectErrorString SnmpAdminString
}
docsBpi2CmIpMulticastIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index of this row."
::= { docsBpi2CmIpMulticastMapEntry 1 }
docsBpi2CmIpMulticastAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of Internet address for
docsBpi2CmIpMulticastAddress."
::= { docsBpi2CmIpMulticastMapEntry 2 }
docsBpi2CmIpMulticastAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Green, et al. Standards Track [Page 25]
RFC 4131 DOCSIS BPI Plus MIB September 2005
"This object represents the IP multicast address
to be mapped. The type of this address is determined by
the value of the docsBpi2CmIpMulticastAddressType object."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 5.4."
::= { docsBpi2CmIpMulticastMapEntry 3 }
docsBpi2CmIpMulticastSAId OBJECT-TYPE
SYNTAX DocsSAIdOrZero
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object represents the SAID to which the IP
multicast address has been mapped. If no SA Map Reply has
been received for the IP address, this object should have
the value 0."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.12."
::= { docsBpi2CmIpMulticastMapEntry 4 }
docsBpi2CmIpMulticastSAMapState OBJECT-TYPE
SYNTAX INTEGER {
start(1),
mapWait(2),
mapped(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the state of the SA
Mapping FSM for this IP."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 5.3.1."
::= { docsBpi2CmIpMulticastMapEntry 5 }
docsBpi2CmIpMulticastSAMapRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CM has transmitted an SA Map Request message for this IP.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
Green, et al. Standards Track [Page 26]
RFC 4131 DOCSIS BPI Plus MIB September 2005
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.10."
::= { docsBpi2CmIpMulticastMapEntry 6 }
docsBpi2CmIpMulticastSAMapReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CM has received an SA Map Reply message for this IP.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.11."
::= { docsBpi2CmIpMulticastMapEntry 7 }
docsBpi2CmIpMulticastSAMapRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CM has received an SA MAP Reject message for this IP.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.12."
::= { docsBpi2CmIpMulticastMapEntry 8 }
docsBpi2CmIpMulticastSAMapRejectErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
noAuthForRequestedDSFlow(9),
dsFlowNotMappedToSA(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Green, et al. Standards Track [Page 27]
RFC 4131 DOCSIS BPI Plus MIB September 2005
"The value of this object is the enumerated
description of the Error-Code in the most recent SA Map
Reject message sent in response to an SA Map Request for
This IP. It has the value none(1) if no SA MAP Reject
message has been received since entry creation."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.12 and 4.2.2.15."
::= { docsBpi2CmIpMulticastMapEntry 9 }
docsBpi2CmIpMulticastSAMapRejectErrorString OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the text string in
the most recent SA Map Reject message sent in response to
an SA Map Request for this IP. It is a zero length string
if no SA Map Reject message has been received since entry
creation."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.12 and 4.2.2.6."
::= { docsBpi2CmIpMulticastMapEntry 10 }
--
-- CM Cert Objects
--
docsBpi2CmCertObjects OBJECT IDENTIFIER
::= { docsBpi2CmObjects 4 }
--
-- CM Device Cert Table
--
docsBpi2CmDeviceCertTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpi2CmDeviceCertEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the Baseline Privacy Plus
device certificates for each CM MAC interface."
::= { docsBpi2CmCertObjects 1 }
docsBpi2CmDeviceCertEntry OBJECT-TYPE
SYNTAX DocsBpi2CmDeviceCertEntry
MAX-ACCESS not-accessible
Green, et al. Standards Track [Page 28]
RFC 4131 DOCSIS BPI Plus MIB September 2005
STATUS current
DESCRIPTION
"Each entry contains the device certificates of
one CM MAC interface. An entry in this table exists for
each ifEntry with an ifType of docsCableMaclayer(127)."
INDEX { ifIndex }
::= { docsBpi2CmDeviceCertTable 1 }
DocsBpi2CmDeviceCertEntry ::= SEQUENCE {
docsBpi2CmDeviceCmCert
DocsX509ASN1DEREncodedCertificate,
docsBpi2CmDeviceManufCert
DocsX509ASN1DEREncodedCertificate
}
docsBpi2CmDeviceCmCert OBJECT-TYPE
SYNTAX DocsX509ASN1DEREncodedCertificate
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The X509 DER-encoded cable modem certificate.
Note: This object can be set only when the value is the
zero-length OCTET STRING; otherwise, an error of
'inconsistentValue' is returned. Once the object
contains the certificate, its access MUST be read-only
and persists after re-initialization of the
managed system."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 9.1."
::= { docsBpi2CmDeviceCertEntry 1 }
docsBpi2CmDeviceManufCert OBJECT-TYPE
SYNTAX DocsX509ASN1DEREncodedCertificate
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The X509 DER-encoded manufacturer certificate that
signed the cable modem certificate."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 9.1."
::= { docsBpi2CmDeviceCertEntry 2 }
--
-- CM Crypto Suite Table
--
Green, et al. Standards Track [Page 29]
RFC 4131 DOCSIS BPI Plus MIB September 2005
docsBpi2CmCryptoSuiteTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpi2CmCryptoSuiteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the Baseline Privacy Plus
cryptographic suite capabilities for each CM MAC
interface."
::= { docsBpi2CmObjects 5 }
docsBpi2CmCryptoSuiteEntry OBJECT-TYPE
SYNTAX DocsBpi2CmCryptoSuiteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains a cryptographic suite pair
that this CM MAC supports."
INDEX { ifIndex, docsBpi2CmCryptoSuiteIndex }
::= { docsBpi2CmCryptoSuiteTable 1 }
DocsBpi2CmCryptoSuiteEntry ::= SEQUENCE {
docsBpi2CmCryptoSuiteIndex Unsigned32,
docsBpi2CmCryptoSuiteDataEncryptAlg
DocsBpkmDataEncryptAlg,
docsBpi2CmCryptoSuiteDataAuthentAlg
DocsBpkmDataAuthentAlg
}
docsBpi2CmCryptoSuiteIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..1000)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for a cryptographic suite row."
::= { docsBpi2CmCryptoSuiteEntry 1 }
docsBpi2CmCryptoSuiteDataEncryptAlg OBJECT-TYPE
SYNTAX DocsBpkmDataEncryptAlg
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the data encryption
algorithm for this cryptographic suite capability."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.20."
::= { docsBpi2CmCryptoSuiteEntry 2 }
Green, et al. Standards Track [Page 30]
RFC 4131 DOCSIS BPI Plus MIB September 2005
docsBpi2CmCryptoSuiteDataAuthentAlg OBJECT-TYPE
SYNTAX DocsBpkmDataAuthentAlg
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the data authentication
algorithm for this cryptographic suite capability."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.20."
::= { docsBpi2CmCryptoSuiteEntry 3 }
-- Cable Modem Termination System Group
docsBpi2CmtsObjects OBJECT IDENTIFIER ::= { docsBpi2MIBObjects 2 }
--
-- SPECIAL NOTE: For the following CMTS tables, when a CM is
-- running in BPI mode, replace SAID (Security Association ID)
-- with SID (Service ID). The CMTS is required to map SAIDs and
-- SIDs to one contiguous space.
--
--
-- The BPI+ base table for CMTSs, indexed by ifIndex
--
docsBpi2CmtsBaseTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpi2CmtsBaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the basic Baseline Privacy
attributes of each CMTS MAC interface."
::= { docsBpi2CmtsObjects 1 }
docsBpi2CmtsBaseEntry OBJECT-TYPE
SYNTAX DocsBpi2CmtsBaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing attributes of
one CMTS MAC interface. An entry in this table exists for
each ifEntry with an ifType of docsCableMaclayer(127)."
INDEX { ifIndex }
::= { docsBpi2CmtsBaseTable 1 }
DocsBpi2CmtsBaseEntry ::= SEQUENCE {
Green, et al. Standards Track [Page 31]
RFC 4131 DOCSIS BPI Plus MIB September 2005
docsBpi2CmtsDefaultAuthLifetime Integer32,
docsBpi2CmtsDefaultTEKLifetime Integer32,
docsBpi2CmtsDefaultSelfSignedManufCertTrust INTEGER,
docsBpi2CmtsCheckCertValidityPeriods TruthValue,
docsBpi2CmtsAuthentInfos Counter32,
docsBpi2CmtsAuthRequests Counter32,
docsBpi2CmtsAuthReplies Counter32,
docsBpi2CmtsAuthRejects Counter32,
docsBpi2CmtsAuthInvalids Counter32,
docsBpi2CmtsSAMapRequests Counter32,
docsBpi2CmtsSAMapReplies Counter32,
docsBpi2CmtsSAMapRejects Counter32
}
docsBpi2CmtsDefaultAuthLifetime OBJECT-TYPE
SYNTAX Integer32 (1..6048000)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object is the default lifetime, in
seconds, that the CMTS assigns to a new authorization key.
This object value persists after re-initialization of the
managed system."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.2."
DEFVAL { 604800 }
::= { docsBpi2CmtsBaseEntry 1 }
docsBpi2CmtsDefaultTEKLifetime OBJECT-TYPE
SYNTAX Integer32 (1..604800)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object is the default lifetime, in
seconds, that the CMTS assigns to a new Traffic Encryption
Key (TEK).
This object value persists after re-initialization of the
managed system."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Appendix A.2."
DEFVAL { 43200 }
::= { docsBpi2CmtsBaseEntry 2 }
docsBpi2CmtsDefaultSelfSignedManufCertTrust OBJECT-TYPE
Green, et al. Standards Track [Page 32]
RFC 4131 DOCSIS BPI Plus MIB September 2005
SYNTAX INTEGER {
trusted (1),
untrusted (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object determines the default trust of
self-signed manufacturer certificate entries, contained
in docsBpi2CmtsCACertTable, and created after this
object is set.
This object need not persist after re-initialization
of the managed system."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 9.4.1"
::= { docsBpi2CmtsBaseEntry 3 }
docsBpi2CmtsCheckCertValidityPeriods OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to 'true' causes all chained and
root certificates in the chain to have their validity
periods checked against the current time of day, when
the CMTS receives an Authorization Request from the
CM.
A 'false' setting causes all certificates in the chain
not to have their validity periods checked against the
current time of day.
This object need not persist after re-initialization
of the managed system."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 9.4.2"
::= { docsBpi2CmtsBaseEntry 4 }
docsBpi2CmtsAuthentInfos OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has received an Authentication Information message
from any CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
Green, et al. Standards Track [Page 33]
RFC 4131 DOCSIS BPI Plus MIB September 2005
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.9."
::= { docsBpi2CmtsBaseEntry 5 }
docsBpi2CmtsAuthRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has received an Authorization Request message from any
CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.1."
::= { docsBpi2CmtsBaseEntry 6 }
docsBpi2CmtsAuthReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has transmitted an Authorization Reply message to any
CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.2."
::= { docsBpi2CmtsBaseEntry 7 }
docsBpi2CmtsAuthRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has transmitted an Authorization Reject message to any
Green, et al. Standards Track [Page 34]
RFC 4131 DOCSIS BPI Plus MIB September 2005
CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.3."
::= { docsBpi2CmtsBaseEntry 8 }
docsBpi2CmtsAuthInvalids OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times
the CMTS has transmitted an Authorization Invalid message
to any CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.7."
::= { docsBpi2CmtsBaseEntry 9 }
docsBpi2CmtsSAMapRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has received an SA Map Request message from any CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.10."
::= { docsBpi2CmtsBaseEntry 10 }
docsBpi2CmtsSAMapReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Green, et al. Standards Track [Page 35]
RFC 4131 DOCSIS BPI Plus MIB September 2005
"The value of this object is the number of times the
CMTS has transmitted an SA Map Reply message to any CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.11."
::= { docsBpi2CmtsBaseEntry 11 }
docsBpi2CmtsSAMapRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has transmitted an SA Map Reject message to any CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.12."
::= { docsBpi2CmtsBaseEntry 12 }
--
-- The CMTS Authorization Table, indexed by ifIndex and CM MAC
-- address
--
docsBpi2CmtsAuthTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpi2CmtsAuthEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the attributes of each CM
authorization association. The CMTS maintains one
authorization association with each Baseline Privacy-
enabled CM, registered on each CMTS MAC interface,
regardless of whether the CM is authorized or rejected."
::= { docsBpi2CmtsObjects 2 }
docsBpi2CmtsAuthEntry OBJECT-TYPE
SYNTAX DocsBpi2CmtsAuthEntry
MAX-ACCESS not-accessible
STATUS current
Green, et al. Standards Track [Page 36]
RFC 4131 DOCSIS BPI Plus MIB September 2005
DESCRIPTION
"Each entry contains objects describing attributes of
one authorization association. The CMTS MUST create one
entry per CM per MAC interface, based on the receipt of an
Authorization Request message, and MUST not delete the
entry until the CM loses registration."
INDEX { ifIndex, docsBpi2CmtsAuthCmMacAddress }
::= { docsBpi2CmtsAuthTable 1 }
DocsBpi2CmtsAuthEntry ::= SEQUENCE {
docsBpi2CmtsAuthCmMacAddress MacAddress,
docsBpi2CmtsAuthCmBpiVersion INTEGER,
docsBpi2CmtsAuthCmPublicKey OCTET STRING,
docsBpi2CmtsAuthCmKeySequenceNumber Integer32,
docsBpi2CmtsAuthCmExpiresOld DateAndTime,
docsBpi2CmtsAuthCmExpiresNew DateAndTime,
docsBpi2CmtsAuthCmLifetime Integer32,
docsBpi2CmtsAuthCmReset INTEGER,
docsBpi2CmtsAuthCmInfos Counter32,
docsBpi2CmtsAuthCmRequests Counter32,
docsBpi2CmtsAuthCmReplies Counter32,
docsBpi2CmtsAuthCmRejects Counter32,
docsBpi2CmtsAuthCmInvalids Counter32,
docsBpi2CmtsAuthRejectErrorCode INTEGER,
docsBpi2CmtsAuthRejectErrorString SnmpAdminString,
docsBpi2CmtsAuthInvalidErrorCode INTEGER,
docsBpi2CmtsAuthInvalidErrorString SnmpAdminString,
docsBpi2CmtsAuthPrimarySAId DocsSAIdOrZero,
docsBpi2CmtsAuthBpkmCmCertValid INTEGER,
docsBpi2CmtsAuthBpkmCmCert
DocsX509ASN1DEREncodedCertificate,
docsBpi2CmtsAuthCACertIndexPtr Unsigned32
}
docsBpi2CmtsAuthCmMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is the physical address of
the CM to which the authorization association applies."
::= { docsBpi2CmtsAuthEntry 1 }
docsBpi2CmtsAuthCmBpiVersion OBJECT-TYPE
SYNTAX INTEGER {
bpi (0),
bpiPlus (1)
}
Green, et al. Standards Track [Page 37]
RFC 4131 DOCSIS BPI Plus MIB September 2005
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the version of Baseline
Privacy for which this CM has registered. The value
'bpiplus' represents the value of BPI-Version Attribute of
the Baseline Privacy Key Management BPKM attribute
BPI-Version (1). The value 'bpi' is used to represent the
CM registered using DOCSIS 1.0 Baseline Privacy."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.22; ANSI/SCTE 22-2 2002(formerly DSS 02-03)
Data-Over-Cable Service Interface Specification DOCSIS 1.0
Baseline Privacy Interface (BPI)"
::= { docsBpi2CmtsAuthEntry 2 }
docsBpi2CmtsAuthCmPublicKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..524))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is a DER-encoded
RSAPublicKey ASN.1 type string, as defined in the RSA
Encryption Standard (PKCS #1), corresponding to the
public key of the CM. This is the zero-length OCTET
STRING if the CMTS does not retain the public key."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.2.4."
::= { docsBpi2CmtsAuthEntry 3 }
docsBpi2CmtsAuthCmKeySequenceNumber OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the most recent
authorization key sequence number for this CM."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.2 and 4.2.2.10."
::= { docsBpi2CmtsAuthEntry 4 }
docsBpi2CmtsAuthCmExpiresOld OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Green, et al. Standards Track [Page 38]
RFC 4131 DOCSIS BPI Plus MIB September 2005
"The value of this object is the actual clock time
for expiration of the immediate predecessor of the most
recent authorization key for this FSM. If this FSM has only
one authorization key, then the value is the time of
activation of this FSM.
Note: This object has no meaning for CMs running in BPI
mode; therefore, this object is not instantiated for entries
associated to those CMs."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.2 and 4.2.2.9."
::= { docsBpi2CmtsAuthEntry 5 }
docsBpi2CmtsAuthCmExpiresNew OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock
time for expiration of the most recent authorization key
for this FSM."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.2 and 4.2.2.9."
::= { docsBpi2CmtsAuthEntry 6 }
docsBpi2CmtsAuthCmLifetime OBJECT-TYPE
SYNTAX Integer32 (1..6048000)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object is the lifetime, in seconds,
that the CMTS assigns to an authorization key for this CM."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.2 and Appendix A.2."
::= { docsBpi2CmtsAuthEntry 7 }
docsBpi2CmtsAuthCmReset OBJECT-TYPE
SYNTAX INTEGER {
noResetRequested(1),
invalidateAuth(2),
sendAuthInvalid(3),
invalidateTeks(4)
}
MAX-ACCESS read-write
STATUS current
Green, et al. Standards Track [Page 39]
RFC 4131 DOCSIS BPI Plus MIB September 2005
DESCRIPTION
"Setting this object to invalidateAuth(2) causes the
CMTS to invalidate the current CM authorization key(s), but
not to transmit an Authorization Invalid message nor to
invalidate the primary SAID's TEKs. Setting this object to
sendAuthInvalid(3) causes the CMTS to invalidate the
current CM authorization key(s), and to transmit an
Authorization Invalid message to the CM, but not to
invalidate the primary SAID's TEKs. Setting this object to
invalidateTeks(4) causes the CMTS to invalidate the current
CM authorization key(s), to transmit an Authorization
Invalid message to the CM, and to invalidate the TEKs
associated with this CM's primary SAID.
For BPI mode, substitute all of the CM's unicast
TEKs for the primary SAID's TEKs in the previous
paragraph.
Reading this object returns the most recently set
value of this object or, if the object has not been set
since entry creation, returns noResetRequested(1)."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.1.2.3.4, 4.1.2.3.5, and 4.1.3.3.5."
::= { docsBpi2CmtsAuthEntry 8 }
docsBpi2CmtsAuthCmInfos OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has received an Authentication Information message
from this CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.9."
::= { docsBpi2CmtsAuthEntry 9 }
docsBpi2CmtsAuthCmRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has received an Authorization Request message from
Green, et al. Standards Track [Page 40]
RFC 4131 DOCSIS BPI Plus MIB September 2005
this CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.1."
::= { docsBpi2CmtsAuthEntry 10 }
docsBpi2CmtsAuthCmReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has transmitted an Authorization Reply message to this
CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.2."
::= { docsBpi2CmtsAuthEntry 11 }
docsBpi2CmtsAuthCmRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the number of times the
CMTS has transmitted an Authorization Reject message to
this CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.3."
::= { docsBpi2CmtsAuthEntry 12 }
docsBpi2CmtsAuthCmInvalids OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Green, et al. Standards Track [Page 41]
RFC 4131 DOCSIS BPI Plus MIB September 2005
DESCRIPTION
"The value of this object is the number of times the
CMTS has transmitted an Authorization Invalid message to
this CM.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Section 4.2.1.7."
::= { docsBpi2CmtsAuthEntry 13 }
docsBpi2CmtsAuthRejectErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedCm(3),
unauthorizedSaid(4),
permanentAuthorizationFailure(8),
timeOfDayNotAcquired(11)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated
description of the Error-Code in the most recent
Authorization Reject message transmitted to the CM. This has
the value unknown(2) if the last Error-Code value was 0 and
none(1) if no Authorization Reject message has been
transmitted to the CM since entry creation."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Sections 4.2.1.3 and 4.2.2.15."
::= { docsBpi2CmtsAuthEntry 14 }
docsBpi2CmtsAuthRejectErrorString OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the text string in the
most recent Authorization Reject message transmitted to the
CM. This is a zero length string if no Authorization
Reject message has been transmitted to the CM since entry
creation."
REFERENCE
"DOCSIS Baseline Privacy Plus Interface Specification,
Green, et al. Standards Track [Page 42]
RFC 4131 DOCSIS BPI Plus MIB September 2005
Sections 4.2.1.3 and 4.2.2.6."
::= { docsBpi2CmtsAuthEntry 15 }
docsBpi2CmtsAuthInvalidErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),